Which Pin Retention Method Should You Use for a Clevis: Clip, Split Pin, Circlip or Locking Pin?
Use a split (cotter) pin for a joint you rarely open, and a reusable clip such as an R-clip for one you open often. A circlip works where the pin has a groove for it. A bolt with a self-locking nut also works if the thread is outside the shear plane. Every method is a […]
How Do You Press-Fit and Retain a Plastic Bushing Without Cracking It, and What Interference Does It Need?
The maker builds the interference into the bushing, so your job is the housing bore: hold the maker’s tolerance, chamfer and deburr the edge, press the bushing in square with a flat press, and measure its bore only after it is in. A pressed-in bushing closes in by roughly the amount of the interference, so […]
How Do Oscillation Angle, Frequency and Sliding Speed Determine the Life of a Spherical Plain Bearing?
A spherical plain bearing wears where its two surfaces slide on each other, so its life depends on how far and how fast they slide, and how hard they press. The swing angle and the swing rate set the sliding speed. The load and the size of the bearing set the contact pressure. Pressure times […]
Which Thread Size, Pitch, Class and Hand Should You Specify on a Linkage Rod, Turnbuckle or Jack Screw?
Give four things, in this order: the nominal diameter, the pitch (or threads per inch), the class of fit, and the hand (right or left). Write inch threads like 3/4-16 UNF-3A and metric ones like M10 × 1.5 – 6g, and add LH for a left-hand thread. Make the thread match the part that screws […]
What Compliance Documents Should I Ask for When a Plastic Bushing Is Used in a Food Plant?
Ask the bushing maker for a written statement that the exact grade meets the food-contact rules for your market. In the US that means the 21 CFR section it falls under, a certificate of conformance or letter of guaranty, the resin grade and whether it is virgin, proof that the additives are listed, and migration […]
How Do I Inspect the Welds Around a Ball Socket for Fatigue Cracks, and Can It Be Repaired?
Clean the area and look first. Cracks start at weld toes, corners and holes, and rust stains or broken paint along a weld can show a crack opening and closing. Confirm anything suspicious with a non-destructive test such as magnetic particle or dye penetrant. Cracks are not normally accepted in welds, and a socket on […]
Why Does a Rod End Wear, Develop Play, Bind, Squeak or Seize, and How Do I Find the Cause?
Almost every rod end problem comes from one of six things: poor installation, too little grease, dirt and water getting in, overload or shock, misalignment, or a harsh environment. They often work together. Read the symptom first, because each one points to a wear mechanism. Then trace back to the first fault in the chain, […]
Should You Replace Only the Spherical Bearing or the Whole Rod Eye on a Hydraulic Cylinder?
Replace only the bearing when it is held by removable retaining rings, the eye’s bore is round and undamaged, and the bearing has not turned in its seat. Replace the whole rod eye when the bearing is permanently staked in, the bore is out of round or damaged, or the bearing has spun in the […]
Why Does an Adjustable Linkage Change Length Under Vibration, and Which Locking Method Works?
The thread inside an adjuster slowly turns when the joint is shaken from side to side or when the load reverses, even if nothing seems loose. The usual fix is a jam nut, a thin nut tightened against the end face of the part so the two lock each other. A thread-locking adhesive, or a […]
How Much Radial Internal Clearance Should a Spherical Plain Bearing Have, and How Do You Check It?
Radial internal clearance is the small play a spherical plain bearing has before it is fitted: how far the inner ring can be moved sideways inside the outer ring. Most bearings are made to the normal group, called N or CN. A tighter group (C2) is for arrangements that want very little play. A looser […]
What Temperature Limits Apply to Steel-on-Steel and PTFE-Lined Spherical Plain Bearings?
There is no single limit. Published figures differ by maker and by design. As a rough picture, one maker rates its standard bearings at −10 °C to +80 °C without restriction, a catalogue gives −50 °C to +150 °C for a steel/PTFE fabric type, and aerospace liner systems reach 200 °C to 330 °C. The […]
What Do the Static and Dynamic Load Ratings on a Rod End Mean?
A rod end usually comes with two load numbers. The static rating is the load it can take once without being permanently damaged. The dynamic rating is used in a life calculation for a joint that moves under load, so it is not a load you can simply apply. When you check a rod end […]