What Is the Difference Between a Weld-On Ball Joint, a Weld-On Ball Socket and a Weld-On Ball End, and What Do Shouldered and Non-Shouldered Mean?
The three names describe one family: a ball pivot with no threaded shank that you weld into a structure, which makes it a permanent pivot. But two different constructions hide behind the names. In one, a ball with a hole through it turns on a pin, inside a welded housing, as in a tractor lift-arm […]
What Is the Difference Between a Jam Nut, a Regular Hex Nut and a Lock Nut, and Which One Should Lock a Rod End Thread?
A regular hex nut is full height and carries the joint’s load. A jam nut is a thin nut, about half the height, used to lock another nut or a threaded part by being tightened against it. “Lock nut” is the broad family of nuts that resist loosening, and a jam nut is one member; […]
How Do You Choose Between a Steel-on-Steel and a Maintenance-Free (PTFE-Lined) Spherical Plain Bearing?
Choose by what the sliding surface needs. A maintenance-free, PTFE-lined bearing suits a pivot you cannot grease, as long as the load, sliding speed, temperature and dirt stay inside the liner’s published limits. A steel-on-steel bearing suits heavy, alternating or shock loads, as long as your machine can keep delivering the specified grease. Neither type […]
When Should a Rod End Be Mounted on a Stud Instead of a Through-Bolt, and How Do You Check the Stud for Bending at the Shoulder, Thread Engagement and Locking?
Use a stud when you can reach the mounting from one side only, or when a bolt head and far-side nut will not fit. The cost is the loading: a stud holds the rod end from one side, in single shear, as a cantilever. Bending, not shear, then decides its size, and the stress is […]
When Should I Use a Plastic Bushing Instead of a Bronze or Steel One, and What Changes If I Swap?
Use a plastic bushing where the load is light to moderate, the joint is wet, corrosive or hard to grease, noise matters, or you want to drop the grease. Keep bronze or hardened steel where the load is heavy or shocked, the heat is high, or you can really keep it greased. A swap is […]
How Do You Tell Why a Spherical Plain Bearing Failed: Wear, Galling, Fretting, Flaking or Liner Delamination?
Read three things together: where the damage is, what it looks like, and what the bearing was doing. Scored surfaces with metal smeared from one side to the other point to galling, which is a lubrication failure. Reddish dust at the fit lines points to fretting. Dents on the ball point to impact or overload. […]
What Pin Diameter, Length, Fit and Hardness Should a Clevis Pin Have?
Take the diameter from the shear and bearing check for your load, make the pin a close but free fit in the holes, make it long enough to reach the retainer, and make the pin harder than the part you want to keep. Diameter and length alone do not specify a pin: retention, shear capacity […]
How Much Misalignment and Axial Load Can a Spherical Plain Bearing Take, and When Do You Need an Angular Contact Bearing?
A spherical plain bearing is built to carry load mainly in the radial direction and to tilt a limited number of degrees each way. Both limits are set by the bearing’s series and size, so read them from the maker’s table. Going past the tilt limit damages the bearing. For a load that pushes along […]
What Shaft Material, Hardness and Surface Finish Should You Use With Plastic Plain Bearings?
Use a hard shaft. A metal bearing, or a hard plastic with a high Shore D rating, can wear away a shaft surface under about 30 HRC, so aim for at least 50 HRC in dirty, abrasive places. Keep the finish neither too smooth nor too rough. Ranges differ from maker to maker, from roughly […]
What Running Clearance Should a Plastic Bushing Have, and Why Does Heat Make a Pressed-In Bushing Tighter, Not Looser?
A plastic bushing needs more clearance than a metal one, and its own fit. Three things change the clearance in service: the press-fit (the bore only reaches its final size after the bushing is pressed in), moisture (nylon swells) and temperature. Temperature works in the opposite direction from what most people expect. A bushing pressed […]
Where Does a Tube-Adapter Joint Fail First: Rod-End Thread, Adapter Thread, Weld or Tube, and How Do I Check Each Under Tension, Compression and Cyclic Load?
The joint is a chain with four links in series: the rod end’s male thread, the adapter’s internal thread, the weld (or pin) into the tube, and the tube wall. Whichever has the lowest capacity fails first, and the best design makes the ductile male thread that link. Check each link on its own, check […]
How Do You Install a Spherical Plain Bearing in a Housing Without Damaging It?
Keep it clean, line it up square with the bore, and push on the ring that is going in, never through the ball. Use a press, not a hammer, and give the parts a lead-in chamfer. Where the fit is tight, use a temperature difference rather than force. Hold the bearing in place with the […]