What Is a Clevis Rod End, Fork Head or Yoke End, and How Do the Types Differ?
A clevis rod end is a U-shaped fork with a cross-hole, screwed on the end of a rod. A pin passes through the fork and the part it joins, so the joint turns in one plane. “Fork head”, “rod clevis” and “yoke end” are names for the same family of part. The types differ in […]
How Do You Choose a Clevis Size and Thread for a Cylinder, Set How Far It Screws On, and Lock It?
Start from the cylinder, not the clevis. Read the thread on the end of the piston rod (diameter, pitch, length and hand) and choose a clevis whose thread matches it. Then match the clevis to the bracket: pin diameter, inside width of the fork and pin centre distance. Screw the clevis on far enough that […]
How Do You Secure a Rod End on a Hydraulic Piston Rod and Stop the Thread Loosening or Galling?
Clean the threads, screw the rod end on to its stop (or the set depth), and lock it: with a thread-locking adhesive, with a jam nut (a second thin nut tightened against it), or both, and tighten to the maker’s torque. Rod ends back off when there is vibration, no locking and the wrong torque. […]
When Should You Use a Clevis Instead of a Spherical Rod End or Rod Eye, and How Much Misalignment Can a Clevis Take?
Use a clevis when the load and the swing stay in one plane and the mounting points are well aligned. It is simple, strong in shear and quick to assemble. Use a spherical rod end when the link moves in more than one plane or the mounting cannot be lined up exactly. A clevis takes […]
How Do I Replace a Worn Lift-Arm Ball Socket: Measure the Old One, Choose a Weld-On End, and Fit It Square?
Find out what is worn first: the pin, the ball or the arm. If the ball end is worn out, measure the old one, because the category, the pin hole and the ball width must all match. Fit a forged weld-on end of that size, or a replaceable ball if your arm has one. Have […]
Ball Joint or Rod End: Which Should You Use on a Pivoting Pneumatic Cylinder?
For an air cylinder that swings and carries the full cylinder force, use a spherical rod end, the part that ISO 8139 calls a rod-end spherical eye. The reason differs by joint. An axial ball joint is pulled apart by the pull stroke, and an air cylinder of 16 mm bore or larger can exceed […]
Turnbuckle, Jack Screw, Adjustable Linkage Rod or Push-Pull Rod: What Is the Difference?
All four let you change the length of a link. A turnbuckle is a body with a right-hand thread at one end and a left-hand thread at the other. A jack screw, in a linkage, is the double-male version of the same idea. An adjustable linkage rod is a complete assembly built to length. A […]
How Do You Calculate the PV Limit and Load Capacity of a Plastic Plain Bearing?
Work out three numbers for your bushing: the pressure on it (p), the speed it slides at (v), and their product, PV, which measures the frictional heat. Each must stay within the limit the material’s maker gives, with room for shock, misalignment and dirt. Pressure is the load divided by bore times length. For a […]
Why Do Turnbuckle and Jack Screw Threads Seize or Gall, and How Do You Free Them and Prevent It?
Galling is a kind of cold welding: under pressure, bare metal touches bare metal as two threads slide, material tears from both faces, and the torn metal fuses across the gap. Fast turning adds heat and makes it worse. It is not rust. It happens most with stainless steel, aluminium and titanium, and it often […]
Which Standards Apply to Rod Ends and Rod Eyes? ISO 12240-4, DIN 648, ISO 6982, ISO 8132 and ISO 8133
Start by working out what you have. A spherical plain bearing rod end, a threaded shank carrying a bearing, is covered by ISO 12240-4. This is the standard that DIN 648 used to cover. A hydraulic cylinder accessory, such as a rod eye or clevis, is covered by ISO 8132 or ISO 8133, depending on […]
Open or Sealed (ES or 2RS)? Which Seals and Materials Suit Dusty, Wet, Corrosive or Washdown Conditions?
In dust or other contamination, choose a sealed type (2RS), and add a boot or wiper where washdown jets reach the joint. The seal keeps dirt out and grease in, but it does not make the bearing waterproof. For corrosive or wet service, the ring and ball material, the sliding pair and a grease that […]
Do Plastic Bushings Need Lubrication, or Can They Run Dry, and What Lubricant Is Compatible?
Often they can run dry. Many plastic bushings are self-lubricating, so they need no grease as long as pressure, speed and PV all stay within the limits of the grade. Beyond those limits you must lubricate or change the material. Where grease is allowed, the lubricant must suit the grade, and in dirty places it […]