How Do You Choose the Pin for a Rod Eye on a Hydraulic Cylinder: Diameter, Material, Fit and Retention?
Size the pin for the cylinder’s maximum force in shear, bending and bearing pressure, not shear alone. Use a hardened and ground steel pin, take the fit from the bearing maker, match the clevis gap to the eye width and make the pin long enough to pass both ears and take its retainer. A pin […]
Which Loads Does Each Hydraulic Cylinder Mounting Style Put on the Rod End?
A mounting style does not load the rod end by itself. It decides whether the cylinder can follow the load as the load moves. If the cylinder can pivot, the rod end mainly feels a straight push or pull. If the cylinder is held rigidly, any misalignment or frame flex is forced into the rod, […]
How Does a Quick-Release Ball Joint Work, and When Is It Better Than a Standard Angle Joint?
A quick-release ball joint has a socket with a spring-loaded outer shell. The shell locks the socket onto the ball stud, so the joint holds without tools. Pull the shell back and the joint comes apart by hand. Push it on again and it relocks, with the linkage length unchanged. Choose it when a link […]
Which Material and Coating Should You Choose for a Linkage Rod or Adjuster in Corrosive or Washdown Service?
The general choice of rod-end material and finish for wet service is in [[K01-Q1-07]]. An adjustable link adds three problems of its own: its threads are turned again and again, so plating wears off at the thread; it joins parts of different metals; and the gaps at the nuts and thread ends hold water. So […]
How Do You Choose Between Acetal (Delrin), UHMW, Nylon and Polyurethane Bushings for an Industrial Machine?
Pick by the main demand. Acetal (Delrin) for a precise, stiff pivot that must hold its size. UHMW for wear, impact and wet or washdown places, where it is soft but very tough. Nylon for shock, as long as you allow for it swelling in water. Polyurethane where you want a bushing that gives and […]
What Should You Know Before Welding a Ball Socket In: Material, Heat, Distortion and Alignment?
Welding is where a weld-on ball joint is won or lost. Weld it to a structure whose steel is known, in a fixture, with the ball and pin lined up, using a procedure written by a qualified person. Heat shrinks and bends things, so use as little weld as the design needs and check that […]
What Do the Letters C, CS, B and BS Mean on an Angle Joint, and When Do You Need a Safety Clip?
On a DIN 71802 angle joint, the letter C means a threaded stud and B means a stud with a rivet end. An added S means a safety clip fitted on the socket. Choose the S version when the joint hangs, when a pull could ever exceed its pull-off value, or when coming apart would […]
Steel, Stainless, Zinc-Plated or Plastic: Which Material Suits a Small Ball Joint?
A standard DIN 71802 angle joint is zinc-plated steel with a greased metal ball seat. It does not have a plastic liner. Use stainless steel where it is wet, washed down, chemical or outdoors. Plastic ball cups exist as separate versions. A PTFE liner belongs in a rod end, not in a standard ball joint. […]
Sleeve, Flanged, Split or Thrust Washer: Which Plastic Bushing Form Do I Need, How Long and Thick Should It Be, and How Do I Avoid Edge Loading?
Choose the form by the loads it must carry and by how it must be fitted. A plain sleeve takes radial load only. A flanged bushing adds a thrust face and keeps itself in place. A thrust washer takes axial load. A split bushing can be fitted without pulling the shaft, but it is weaker. […]
How Do You Set the Length of a Ball Joint Linkage Rod, and Which Thread Size and Hand Should You Choose?
Set the length as the distance between the two ball centres, measured with the rod at the middle of its adjustment. Use a right-hand thread on one end and a left-hand thread on the other, and you can turn the rod to change its length without removing either end. Each full turn then changes the […]
How Do You Find and Reduce Backlash or Lost Motion in an Adjustable Linkage?
Backlash is play: the small movement at the input that does nothing at the output before the linkage takes up the slack. Find it by moving the input one way until the output follows, zeroing a dial indicator on the output, moving away and back to the same input position, and reading the difference. Then […]
Which Rod End Material and Finish Suits Wet, Corrosive or Washdown Service: Zinc-Plated Steel, Alloy Steel or Stainless?
For wet or washdown service, stainless steel is the usual first choice, because plated carbon steel and alloy steel rust as soon as the coating is worn through in a place that stays wet. Stainless costs more and has slightly lower load capacity. A polymer rod end resists rust, but it is weaker. Zinc plating […]