What Bore, Bolt, Pin Tolerance and Mounting Arrangement Should You Use for a Rod End: Single or Double Shear, Spacers and Clamping the Inner Ring?
Mount the rod end between two supports, a fork or clevis, wherever you can, so the pin is in double shear. Use a hardened, ground pin or bolt with a snug but free fit in the ball bore. Clamp the inner ring so the ball does not turn on the pin, but not so hard […]
How Is a Weld-On Rod Eye Attached and Inspected, and How Do Weld Failures Show Up?
A weld-on rod eye is welded at manufacture, on a prepared weld zone of the rod end or bracket, under a qualified procedure, so the weld carries the cylinder load. Welding on a finished, hardened, chrome-plated rod in the field is not a repair. Weld only where appropriate, keep heat away from seals and finished […]
Why Does a Plastic Bushing Wear, Seize, Squeak, Swell, Crack or Walk Out of Its Housing?
Almost always it is one of five things: too much load or speed (heat), a shaft that is too soft or too rough, a bore that closed up or opened out, a housing fit that lost its grip, or grit, water, chemicals or temperature that the material does not suit. The debris and the damage […]
How Should a Rod End or Clevis Be Attached to a Tube in a Machine Linkage: Weld-In Adapter, Pinned or Bolted Insert, or Threaded-In Insert?
Use a weld-in adapter when the joint is permanent and you can weld to a procedure. Use a pinned or bolted insert when you cannot weld or must take the link apart, and accept that the holes in the tube wall set the strength. Use a threaded insert in a thick-walled or internally threaded tube […]
Which End Fitting Suits an Adjustable Linkage Rod: Clevis, Rod End, Ball Joint or Eye End?
Ask how the two ends need to move. If the link and its mounting stay in one plane, a clevis with a pin is simple, rigid and easy to fit. If the ends have to tilt out of that plane, use a rod end or ball joint, which swivel on a ball. If neither end […]
Why Do Spherical Rod End Bearings Wear, Develop Play or Fail on Hydraulic Cylinders, and How Do You Inspect Them?
On hydraulic cylinders, spherical rod end bearings usually fail for a short list of reasons: too little grease, dirt and water getting into the joint, misalignment that loads one edge, shock or hammer damage, and a loose fit in the eye or on the pin. Many of these start at installation. There is no general […]
How Do You Connect an Angle Joint to a Cylinder Rod, Threaded Rod or Bracket, and How Deep Should the Thread Go?
An angle joint has two threads: an internal thread in the socket and an external thread on the stud. Screw the socket onto a rod, and the stud into a tapped hole or through a plate with a nut. Match the thread type and pitch exactly. Engage the thread about 1.0 to 1.5 times its […]
How Do You Size a Spherical Plain Bearing: Load Ratings, Safety Factor, Shock and Reversing Loads?
Sizing is three checks in a row. First turn the radial and axial loads into one equivalent load P. Then check the static rating C₀ against P with a safety factor. Then, if the bearing swings under load, check the contact pressure and sliding speed (pV) and the life by the maker’s method. The worked […]
What Does a Plain, Cone or High-Misalignment Spacer Do, How Long Should It Be, and How Much Extra Tilt Does It Really Give?
A spacer sits between the ball of a rod end and the bracket. A plain spacer centres the rod end and sets the bolt size. A cone spacer does the same while narrowing the part that stands inside the housing opening. A high-misalignment spacer is tapered further so the housing can tilt more before it […]
How Do You Find the Misalignment Angle a Rod End Needs, and the Angle It Really Has Once It Is Installed?
Work out the largest angle the linkage swings through, in each direction. Then find the angle the rod end can tilt before something touches. The catalogue gives the second number for the bare rod end, but the clevis, bolt head, washers and spacers usually cut it. The angle you need must be smaller than the […]
Why Does a Cylinder Clevis Wear, Rattle or Crack at the Pin, and When Should the Fork Head, Pin or Bracket Be Replaced?
Most pin-joint trouble starts as clearance. The pin, its bushing or the bore wears, the joint begins to rattle, and the play then turns a steady load into repeated hammering until a fork ear or the thread cracks. The usual causes are a pin that is too soft, too small or overloaded, grease that is […]
What Grease, How Much and How Often for a Steel-on-Steel Spherical Plain Bearing, and How Do the Lubrication Holes and Grooves Work?
Use a lithium-soap extreme-pressure grease, grease the bearing while it is unloaded, and keep adding until fresh grease shows between the inner and outer rings. How often depends on what the duty does to the grease: heavy one-direction load, small swing angle, heat, dirt and water all shorten it. As a guide, one maker puts […]