What Is the Maximum Operating Temperature of a Plastic Bushing, and What Happens as It Heats Up?
There is no single maximum for plastic bushings. Each grade has its own continuous limit, a higher short-term limit, and often a lower temperature above which the bushing needs to be secured in its housing. The temperature that counts is the ambient plus the heat the bushing makes itself. As it heats up, a plastic […]
How Do You Size a Small Ball Joint for an Actuator or Air Cylinder Linkage?
First work out the force the actuator can produce: pressure times piston area. Then ask which way that force pushes on the joint, because “axial” means different things on different joints. Find the bending the stud sees (force times the distance to its support), check the stud, the thread and the retention, and apply a […]
How Do Spherical Rod Ends Prevent Side Loading on a Hydraulic Cylinder, and Can a Worn Rod End Damage It?
A spherical rod end does not stop side loading by carrying the sideways force. It removes one cause, an angle error at the rod end, by letting the rod end tilt so the cylinder force stays along the rod. A worn rod end can add to the problem: play lets the load line move and […]
How Does Rod Eye Mounting Affect Hydraulic Cylinder Buckling and Column Strength?
How the rod eye and the other end are mounted sets the rod’s effective length, and the effective length decides how much push the rod can take before it bows sideways. A fully fixed mounting gives the highest column strength. Pinned ends, such as a clevis and a rod eye, give much less. A bigger […]
How Do You Size an Adjustable Linkage Rod or Turnbuckle for Tension and Compression Loads?
Find the largest force the link sees, pulling and pushing. Follow it through the load path and find the weakest part: the thread on the rod or stud, the thread inside the body, the tube, the rod-end shank or the pins. Work out each limit from the stress area of the thread, or take it […]
How Much Can a Small Ball Joint Tilt, and How Do You Set Up a Linkage So It Does Not Bind?
Catalogs list the tilt of a DIN 71802 angle joint as 18° without a safety clip and 15° with one. One maker lists ±18° for its CS joint instead, so always read the drawing for your part. The limit is where the stud’s neck touches the socket rim. To keep a linkage from binding, point […]
What Do GE, GEH, GEG and GEEW Mean on a Spherical Plain Bearing, and What Do the Suffixes ES, 2RS and TX Mean?
The letters are a maker’s shorthand laid on top of the ISO 12240-1 dimension series, which fixes how outside diameter and width relate to the bore. GE is the common metric radial type. GEG, GEH and GEEW point to a wider or larger-diameter series, or to an extended inner ring. The suffixes describe details: E […]
How Strong Is the Shank of a Male Rod End: Thread Tension, Bending, Fatigue and Breakage?
The shank usually fails at its thread, because the thread is where the section is smallest and the root concentrates stress. Its pulling strength depends on the stress area at the thread’s minor diameter, not on the outer diameter. A small off-axis load adds bending that can be several times larger than the pull, and […]
How Do You Specify a Male or Female Rod End, and How Do You Choose Right-Hand, Left-Hand or Both Threads for an Adjustable Linkage?
Choose male if the mating part has an internal thread, and female if it has an external one, such as a rod or stud. Then write the thread size, pitch and hand, and check them against the real part rather than a photo. Right-hand is the default. For a link you need to lengthen or […]
How Do I Choose Tube Diameter and Wall Thickness for a Push-Pull Link or Frame Member: Buckling, Bending and Torsion, and How Much Do the Adapter Ends Change the Answer?
For a link that pushes, buckling decides the tube, not strength. Treat the link as a column with a pin at each end, work out its slenderness L ÷ r, and use the Euler formula if it is slender and the Johnson formula if it is not. A tube beats a solid rod of the […]
How Do You Install and Align a Push-Pull Rod to Avoid Binding and Side Loading?
Make the force pass straight along the rod from one pin to the other. Fit a rod end or ball joint at each end so the rod can swing freely, and check through the full travel that nothing touches, nothing sticks, and the ends are not at the limit of their tilt. Keep enough thread […]
How Do You Write an RFQ for Custom Rod Ends, Bearings, Bushings and Linkage Parts?
Write the request so that someone who has never seen your machine could quote and build the part from it alone: the part itself (a drawing with its revision, or a part number plus the key sizes), the material and its grade, the finish, how the part is loaded and where it works, the quantity […]