How Long Can a Push-Pull Rod Be Before It Buckles, and What Rod Diameter Do You Need?
A rod that pushes can bow sideways long before the steel is overloaded. How much push it can take falls with the square of its length and rises with the fourth power of its diameter. For a straight round steel rod with a pin at each end, the diameter you need is d = (64 […]
When Should a Spherical Plain Bearing Be Replaced: Measuring Play, Inspection and Wear Limits?
Replace it when it has used up the play, torque, noise or condition you decided you can accept. There is no single wear limit for all spherical plain bearings, so set your own limit with the maker’s figures before the bearing goes into service. Check by unloading the joint, cleaning it, and moving the ball […]
Should I Choose a PTFE-Lined, Metal-to-Metal or Bronze-Race Rod End for Machine Duty?
Choose a PTFE-lined rod end where you cannot grease it and the load, speed and temperature sit inside the liner’s limits. Choose a metal-to-metal or bronze-race rod end, with grease, where the load is heavy or shocked and you will keep it greased. Start from the duty, not the construction name. None of the three […]
How Do You Choose a Three-Point Hitch Ball and Pin for the Implement Category (Category 0 to 4)?
The category tells you the pin sizes and the linkage layout. It does not tell you the lift capacity. Measure the bare pins on the implement, find the category from their size, then choose the ball or socket whose bore fits that pin and the bushing or sleeve that goes with it. Horsepower alone does […]
How Often Should Linkage Rods, Turnbuckles and Jack Screws Be Inspected and Lubricated, and When Do They Need Replacing?
There is no general interval for machine linkages. The machine’s manual or the maker of the part sets it, and where neither does, the maintenance plan should set it from the load, the environment and the cost of a failure. Look for a length that has drifted, a jam nut that has turned, play, damaged […]
What Shaft and Housing Fits, Tolerances and Surface Finish Does a Spherical Plain Bearing Need?
The outer ring is normally pressed into the housing (H7 only for light loads where axial movement is needed), and the inner ring is fitted to the shaft with a clearance or a light interference, depending on how the load acts. As a common starting point, one maker’s table lists an h6 hardened shaft for […]
How Much Pull-Off Force Does a Ball Socket Hold, and How Do You Stop a Ball Joint from Coming Apart?
Catalogs list a minimum pull-off force of 30 to 100 N for ball sizes from 8 to 19 mm. That figure is how firmly a new socket holds a ball when pulled straight off. It is not a working load. To stop a joint separating in vibration or shock, keep pulling loads away from the […]
Plain Rod Eye or Spherical Rod End on a Hydraulic Cylinder: Which Should You Use?
Use a plain rod eye when the rod moves in one flat plane, and both pins are parallel and held rigidly. Use a spherical rod end when the rod’s movement leaves that plane, when the structure bends under load, or when the brackets cannot be kept in line. A spherical joint lets the rod tilt, […]
What Types of Rod Ends and Rod Eyes Are Used on Hydraulic Cylinders, and How Do They Differ?
A rod end or rod eye is the metal part that joins the end of a cylinder’s piston rod to the machine. The rod pushes and pulls, and the rod end passes that force on through a pin. Rod ends differ in three independent ways: how they attach to the rod, how they join the […]
How Do I Size a Tube Adapter to a Real Tube: Inside-Diameter Tolerance, Weld Seam, Seating Shoulder, Thread Size Limits and Which Tube Standard Controls the Fit?
The adapter fits the real inside of the tube, not the nominal one. The inside diameter moves with the outside-diameter tolerance, the wall tolerance and the out-of-roundness, and a welded tube may have a seam inside. Size the adapter to the smallest inside diameter it must enter, check the gap at the largest, choose a […]
What Limits the Load of a Clevis Joint, and How Do You Check Pin Shear?
A clevis joint is only as strong as its weakest part, and there are four to look at: the pin (shear, bending and bearing pressure), the lugs and fork around the pin holes, the thread that joins the clevis to the rod, and the rod itself. For the pin, the average shear stress in double […]
What Causes a Spherical Plain Bearing to Squeak, Stick, Bind or Show Stick-Slip, and How Do You Fix It?
The most common cause of squeaking and jerky movement is stick-slip: the surfaces grip, then let go, then grip again, because it takes more force to start sliding than to keep sliding. A lack of lubrication, a worn-in or very smooth surface, a bearing clamped too tight, and misalignment can each make it worse. Find […]